Chris Hagen owns Inertia Laboratory, a suspension shop in the DFW area that rebuilds, revalves and dyno tests shocks and sells high-end coilover systems. Most of his customers never visit. They ship their dampers in, and Inertia Lab ships them back rebuilt and tested.
In episode 214 of Do It For A Living, host Kevin Dubois and co-host Richard Fielder talk with Chris about how he got into damper work, what a shock dyno tells you, and how he runs a three-person service business out of 1,200 square feet. The article covers both the technical and business sides.
From Formula SAE to owning the shop
Chris studied mechanical engineering at UT Arlington and spent two years on the Formula SAE suspension team. A friend worked at AST/Moton, and Chris kept asking if they were hiring. When a spot opened, he started as a tech and learned rebuilds and the dyno by doing them.
After college he took an engineering job at Peterbilt and kept working on shocks on the side. When the person running the shop burned out, Chris and a partner bought the equipment for about 10 cents on the dollar. They started at the end of 2015. Neither was full time the first year, and revenue stayed under $100,000. Some weeks ran to 95 hours.
He went full time at the end of summer 2021. Before he quit, he saved enough to live modestly for a year to a year and a half. He used every bit of it, and the money ran out right about when the business could pay him a small wage.
Who sends shocks to Inertia Lab
The service side is mostly on-road trucks, such as Toyota Tacomas and 4Runners running King and Icon shocks. Inertia Lab is listed on Icon's website as a Texas rebuilder, which brings in steady work. Chris did Fox for a while but stopped, because parts were hard to get and expensive without a discount.
New product sales go mostly to performance street cars with electronic dampers and to circuit racers. Chris has passed on side-by-sides and mountain bikes. The shop is near the limit of how many brands it can keep parts for.
How to tell a shock needs a rebuild
The most common sign is a leak, either a puddle or a damp top. A clunk is the next one. People often blame a top mount, but a clunking shock is usually out of nitrogen. It cavitates, then slams into a wall of fluid on the return. On MacPherson struts, worn upper bushings and bearings can clunk too. Beyond that, Chris goes by mileage or hours. Dampers do degrade slowly, but that loss is hard to feel.
What a shock dyno does, and why Chris stopped sending reports
A shock dyno is a linear actuator with a load cell and a position sensor, run through software. Common machines use a Scotch yoke that makes a sine wave at a set speed and records force at peak velocity. Constant-velocity machines measure force through the whole stroke.
Every shock is dynoed before it leaves Inertia Lab. For road racing work, the main job of the dyno is to prove the shock works and that a pair matches.
The shop used to send a dyno report with every job. The plots confused people, and each one led to a call about damping ratios at a given click. Thirty minutes on the phone per set was too much, so reports now go only to customers who ask.
Customers almost never send data logs. Most bring driver feedback, and sometimes the real problem is an alignment done years ago. Chris has a stock Corvette he plans to set up for testing, because tuning ride quality on cars he almost never sees only gets so close.
Running the shop day to day
Inertia Lab is Chris and two others in about 1,200 square feet, with a single bay, a lift, racks and benches. His brother handles operations and had no automotive background, so training has taken time.
The jobs are split on purpose. The operations person does intake. He bins the shocks, takes photos, removes the springs, cleans everything and puts it in the ready-to-rebuild slot. The tech takes it from there and only stops to talk when something is wrong, unfamiliar, or needs parts. The operations person then picks the job up from a column on the shop's kanban board in My Shop Assist and orders the parts. Chris fills the gaps. He works out lengths for custom builds, spots an old shaft that looks like the others but isn't, and calls Öhlins when a part isn't on his laminated reference sheet.
His standard operating procedures mostly cover the flow in and out, such as intake, inspection photos, billing and shipping. Brands differ so much that technical SOPs stick to key points. When Chris did every rebuild himself in the old Dallas shop, a pegboard held only the tools he used most, with common seals below and the dyno to his left. He never took two steps for a tool, and he thinks he worked faster there than the shop does now.
A monthly meeting with a mentor keeps the bigger picture moving. Each quarter they set a few core goals and break them into weekly tasks. Chris admits the hard part is getting them done before emails and calls take over the day.
Pricing, payments, shipping and saying no
Most shock jobs are flat rate. Pricing every shim and every bit of oil would confuse customers, and a set price is close to accurate anyway. Exploratory work and revalving bill at a labor rate. A rebuild runs around $1,000 or a little more. A new set can be $7,000 or $8,000, and some now reach five figures.
Dealers make up about half the business. They pay by ACH because their discount is already the lowest margin Chris will accept, and a card fee of around 3 percent would eat much of what's left. Shops can be harder customers than individuals, since some expect a drop-off and next-morning pickup. Chris never wants anyone to wait more than two weeks, though overseas parts can stretch that.
Shipping goes direct through FedEx. Chris keeps calling for a bigger discount and gets a real one. Boxes stay under 50 pounds because the price jumps sharply above that, so heavy orders get split into two boxes.
Chris also turns work down. Cheap imported shocks usually have no parts available. Some designs come in several variants and fail the dyno for any of a dozen reasons. He stopped working on those rather than send out shocks below his standard.
Everything we sell, we service first, or at the very least we need to see the insides.
That rule decides which brands Inertia Lab sells. He has dropped one brand before and has another on pause over product and supply problems. When a customer spends $7,000 on a three-way setup, Chris expects to spend at least 20 minutes explaining it and giving a starting setting.
You need to know how to use them, otherwise why did I sell them to you?
Two-way, three-way and electronic dampers
A two-way shock adjusts rebound and compression. A three-way usually adds a second compression adjustment. On a common remote-reservoir design, the "high-speed" knob sets how much pressure builds before a poppet valve opens, and the "low-speed" knob opens a bypass around it. If high speed is turned all the way down, adjusting low speed does almost nothing. Chris sees a two-way as better than no control and a three-way as the better tool when the budget allows.
Electronic dampers are growing on the street side. A proportional solenoid valve does the work, and the controller matters as much as the shock or more. Next, Chris wants to get more from the website he launched in April 2025 and to make more of his own parts, so supplier problems hurt less.
Key takeaways
- Save a runway before going full time. Chris saved a year to a year and a half of living costs and used all of it.
- Split intake, tech work and ordering into separate roles so the tech only stops when something is wrong.
- Don't send information nobody asked for. Unrequested dyno reports cost 30-minute calls without helping customers.
- Turn down work you can't get parts for or can't send out to your own standard.
- Service a product before you sell it, and set dealer payment terms that protect a thin margin.
- Keep shipments under the weight steps that sharply raise the price.
Tracking a service shop with My Shop Assist
Inertia Lab runs its job flow in My Shop Assist. Website form submissions from JotForm drop straight into a new job, and kanban columns show who has each set of shocks, from intake to parts ordering to the bench. Kevin also showed MSA's new QR code labels in this episode. A tag on a shock, an engine or a set of keys opens the job from a phone camera or a barcode scanner. If you run a service-heavy performance shop, see how My Shop Assist works for performance and racing shops.
You can try it with your own jobs and workflow when you start a free 30-day trial.
Related episodes: 216 - How to Set Your Shop Labor Rate and Measure Efficiency and 210 - How a Formula SAE Team Funds and Builds an EV Race Car.
Listen on the Do It For A Living podcast site, and visit Inertia Laboratory at inertialaboratory.com.




